Search found 1070 matches
- Mon Jan 29, 2007 6:48 pm
- Forum: Suzuki MightyBoy
- Topic: Gadj's MB running but still need wiring diagram.
- Replies: 2
- Views: 602
Gadj's MB running but still need wiring diagram.
Well. I finally have my M.B. running. I have been slowly eliminating possibilities but the breakthrough was thanks to a comment made by John Rooth in 4wd Monthly,s Bush Mechanic's Challenge 2 while working on his Pajeros fuel pump 'In the old days you would put a jerry can on the roof & run a ho...
- Thu Jan 25, 2007 9:54 pm
- Forum: Suzuki MightyBoy
- Topic: door handles
- Replies: 7
- Views: 1075
- Thu Jan 25, 2007 9:33 pm
- Forum: Suzuki MightyBoy
- Topic: adaptor plate
- Replies: 66
- Views: 13517
- Sun Jan 21, 2007 2:46 pm
- Forum: Suzuki Alto / Hatch
- Topic: Worlds most expensive head job.
- Replies: 28
- Views: 6017
Hey, Pony tail - you had better click on Colins profile buttton, you will find he has his tongue firmly planted in his cheek when he knocks his own trade - from what I have seen in Colins posts, he is one of the trustworthy many who are shot down by the actions of the dodgy/greedy/unscrupulous few.....
- Wed Jan 17, 2007 10:09 pm
- Forum: Suzuki MightyBoy
- Topic: Cracked Exhaust
- Replies: 7
- Views: 1019
Have a look at www.por15.com.au their 'Fire Seal' should repair your manifold efectively. Your alternative is to have extractors made up - why bother when you will have to have extractors or manifold custom fitted for the turbo. Fire seal will cost around $30.00 - extractors over $150.00.
Gadj.
Gadj.
- Sat Jan 13, 2007 10:05 pm
- Forum: Suzuki MightyBoy
- Topic: stripping the tray
- Replies: 10
- Views: 1288
- Tue Jan 09, 2007 2:34 pm
- Forum: Wanted to Buy
- Topic: front end rubbers
- Replies: 8
- Views: 1146
- Wed Dec 20, 2006 10:18 pm
- Forum: Wanted to Buy
- Topic: Wanted: F5A engine mounts.
- Replies: 10
- Views: 1931
- Wed Dec 20, 2006 9:55 pm
- Forum: General Discussion
- Topic: I need help
- Replies: 3
- Views: 702
- Mon Dec 18, 2006 9:51 pm
- Forum: General Discussion
- Topic: MB off the clock
- Replies: 33
- Views: 6084
115 back to 110 ain't so bad... used to drive a Honda TN350 (like a Carry trayback but only 2cyls air cooled rear eng). It would make 105Km/h flat out on the flat but that same truck that robbed you of 5Km/h would have left the TN350 doin' 60Km/h. I sadly miss that little truck - it was amazing what...
- Mon Dec 11, 2006 11:23 pm
- Forum: Wanted to Buy
- Topic: Wanted: F5A engine mounts.
- Replies: 10
- Views: 1931
- Mon Dec 11, 2006 11:16 pm
- Forum: Suzuki MightyBoy
- Topic: Part numbers
- Replies: 2
- Views: 643
Once again check out www.garrmax.com.au and if you're concerned by heat ask them if a viton seal would be apropriate.
Gadj
Gadj
- Mon Dec 11, 2006 11:09 pm
- Forum: Suzuki MightyBoy
- Topic: Where to source engine bearings?
- Replies: 16
- Views: 4687
Try www.garrmax.com.au. I can't guarantee their help but I know they helped the previous owner of my MB out with bearings for the F8B - they found Matiz bearings were suitable. Go figure!
Gadj.
Gadj.
- Fri Dec 01, 2006 9:47 pm
- Forum: Wanted to Buy
- Topic: Wanted: F5A engine mounts.
- Replies: 10
- Views: 1931
Ok your'e all welcome to the info but please read my initial reply to Mommers again - carefully. Mommers can follow directions (Thankyou) I'm sure you can too. :P Mommers, some mounts are avail new some can be substituted. I can't get my solution to post here - too long, P.M. me with your email &...
- Thu Nov 30, 2006 7:01 pm
- Forum: Wanted to Buy
- Topic: Wanted: F5A engine mounts.
- Replies: 10
- Views: 1931