what is the real stud patten for my 1987 square light alto works?
Also do the coilovers kit you can get from monster for the round lights model(CN/CP21S,CR/CS22S) fit my square light model?
http://www.monster-sport.com/e/car/alto ... l#CR/CS22S
you would think the it will bolt up the same.
my rear shocks are stuffed im bunny hoping all over the place hahaha
will these wheels fit my Alto RSR CV7
-
Goofy[HSK]
- Posts: 630
- Joined: Tue Nov 15, 2005 9:33 pm
- Location: South Australia
- Contact:
Pretty certain they're 4x114.3, 10mm stud
I would also think that suspension would bolt straight up.
I would also think that suspension would bolt straight up.
'89 Alto Works RS/R - Awaiting: Paint, Windscreen, Compliance, Lottery
'89 Alto Works RS/R - Complied, Registrable, Awaiting Paint, Engine not running
www.hillsidekonnection.com
'89 Alto Works RS/R - Complied, Registrable, Awaiting Paint, Engine not running
www.hillsidekonnection.com
-
lunacy20bfd
- Posts: 58
- Joined: Tue Jul 26, 2011 5:35 pm
ok i am getting closer to what i am going to buy for wheels
http://otomoto.com.au/p/5370898/nemoto- ... x7-20.html
I can get these from otomoto with 165/45 tires fitted for $1100 delivered
I looked at the tire calc on here and it look like they might stick out 20mm , but then I can roll the guards and that might fix it lol ?
If I could adjust the camber that would help a lot but I don’t think I can unless I get coilovers with adjustable camber tops?
Hmm thinking
i have attached a pic of my car
http://otomoto.com.au/p/5370898/nemoto- ... x7-20.html
I can get these from otomoto with 165/45 tires fitted for $1100 delivered
I looked at the tire calc on here and it look like they might stick out 20mm , but then I can roll the guards and that might fix it lol ?
If I could adjust the camber that would help a lot but I don’t think I can unless I get coilovers with adjustable camber tops?
Hmm thinking
i have attached a pic of my car
- Attachments
-
-
lunacy20bfd
- Posts: 58
- Joined: Tue Jul 26, 2011 5:35 pm
Federal FD1 165/45 is what the tires will be
The only way those wheels will fit is with bolt-on flares. You might have a snowflake's chance otherwise if they were higher offset.
F8B EFI turbo - Three pots and a snail.
-
lunacy20bfd
- Posts: 58
- Joined: Tue Jul 26, 2011 5:35 pm
is the adjustable for camber?
Also where would i get bolt on flares for this car?
would 155/45 be to much strech or not worth doing? lol
Also where would i get bolt on flares for this car?
would 155/45 be to much strech or not worth doing? lol
- Attachments
-
-
If you want adjustable camber then you'd need to install either plates or pins. Either way you'll need oni-kyan to get those wheels on!
F8B EFI turbo - Three pots and a snail.
-
Goofy[HSK]
- Posts: 630
- Joined: Tue Nov 15, 2005 9:33 pm
- Location: South Australia
- Contact:
http://forums.beyond.ca/showthread/t-241435.html
http://driftwest.ca/forums/threads/proj ... 383/page-6
Must be FF though
http://driftwest.ca/forums/threads/proj ... 383/page-6
Must be FF though
'89 Alto Works RS/R - Awaiting: Paint, Windscreen, Compliance, Lottery
'89 Alto Works RS/R - Complied, Registrable, Awaiting Paint, Engine not running
www.hillsidekonnection.com
'89 Alto Works RS/R - Complied, Registrable, Awaiting Paint, Engine not running
www.hillsidekonnection.com
-
lunacy20bfd
- Posts: 58
- Joined: Tue Jul 26, 2011 5:35 pm
Hahaha
camber pins sound cheap . where can i get them from?
also the camber plates for a altoworks where can i get them from?
camber pins sound cheap . where can i get them from?
also the camber plates for a altoworks where can i get them from?