adaptor plate

MightyBoy tech questions and answers.
User avatar
jono
Posts: 453
Joined: Sun Dec 04, 2005 6:18 pm
Location: Hobart, Tassie

hey

wanna know what's involved in making a (decent) adaptor plate for my dual throat webber. for the people that have put on webber's, where did u get the adapter plate made up. did u go to an engineer to get it done properly or just whip one up?

thanks,

jono
Speed Limited: I'm Pedalling as Fast as I Can
1987 Mighty Boy
Injected F8B (love it!)

http://www.freewebs.com/fitre/
User avatar
Brayden
Posts: 9101
Joined: Sun Apr 11, 2004 3:09 am
Location: Canberra ACT
Contact:

I bought a Datsun Weber adapter plate by Redline.
F8B EFI turbo - Three pots and a snail.
User avatar
jono
Posts: 453
Joined: Sun Dec 04, 2005 6:18 pm
Location: Hobart, Tassie

oh okay, that was for a 32/36 though wasn;t it? will i have trouble with the dual throats going into a single hole, like needing a funnel shaped adaptor plate? don't suppose anybody would know what adaptor plate i could get for mine, the 30DIC?

thanks,

jono
Speed Limited: I'm Pedalling as Fast as I Can
1987 Mighty Boy
Injected F8B (love it!)

http://www.freewebs.com/fitre/
User avatar
Brayden
Posts: 9101
Joined: Sun Apr 11, 2004 3:09 am
Location: Canberra ACT
Contact:

My weber was dual throat, and the adapter plate was a funnel of sorts. ;)
F8B EFI turbo - Three pots and a snail.
User avatar
jono
Posts: 453
Joined: Sun Dec 04, 2005 6:18 pm
Location: Hobart, Tassie

okay, cool. will see what i can find with redline.

thanks,
jono
Speed Limited: I'm Pedalling as Fast as I Can
1987 Mighty Boy
Injected F8B (love it!)

http://www.freewebs.com/fitre/
User avatar
fritz
Posts: 711
Joined: Fri Apr 16, 2004 11:21 am
Location: Perth WA

Hey guys.
I know Jono has fitted one of these weber carbs. I think he mentioned he drilled out the base of the carb to make it fit?

I haven't done any running around for an adapter yet, but was wondering if the base hole spacing would be the same for a 30dic as they are for other smaller webers?

Does anyone out there maybe have the base dimensions of a 32/36 or something like it? :) :)
mowog
Posts: 970
Joined: Sun Apr 25, 2004 2:22 am

I got a Weber 34admic it came off a XE Falcon.
would this be any good for the F8? with rejetting maybe? What jets?
User avatar
Brayden
Posts: 9101
Joined: Sun Apr 11, 2004 3:09 am
Location: Canberra ACT
Contact:

Weber off a 4L falcon? Don't think you'd get close to tuning it for an F8B!
F8B EFI turbo - Three pots and a snail.
mowog
Posts: 970
Joined: Sun Apr 25, 2004 2:22 am

They run them in geminis.
Anyone got a good 32/36 to swap?
mowog
Posts: 970
Joined: Sun Apr 25, 2004 2:22 am

Probablybe a bit breathless tho.
User avatar
fritz
Posts: 711
Joined: Fri Apr 16, 2004 11:21 am
Location: Perth WA

Hello... Help needed :? :D

If I were to buy another weber for my car, and I probably will for my 'good' engine, I'd be seriously looking at a weber 28/36 (or 34?) that came off performance cortinas and the like.
User avatar
Brayden
Posts: 9101
Joined: Sun Apr 11, 2004 3:09 am
Location: Canberra ACT
Contact:

Any of the DGV Webers use the same base plate Fritz. All you need is an off-the-shelf Redline Datsun adapter plate.
F8B EFI turbo - Three pots and a snail.
User avatar
fritz
Posts: 711
Joined: Fri Apr 16, 2004 11:21 am
Location: Perth WA

Excellent!!!
Any particular type of datsun I should be looking for, or are they all the same?

Thanks. :)
User avatar
Brayden
Posts: 9101
Joined: Sun Apr 11, 2004 3:09 am
Location: Canberra ACT
Contact:

1000, 1200, 1600 - they should all be the same. ;)
F8B EFI turbo - Three pots and a snail.
User avatar
fritz
Posts: 711
Joined: Fri Apr 16, 2004 11:21 am
Location: Perth WA

I've just emailed redline products to find out about the adaptor & will post details when I receive them.

Brayden, could you tell me if the adaptor that you used rotated the carb through 90 degrees? I've not seen one, but it seems like that is the most likely way of doing this. :?
One of the pics in your album suggests otherwise though.

Image
Post Reply