Search found 58 matches
- Sun Oct 04, 2009 7:20 am
- Forum: For Sale
- Topic: [SOLD] Mighty Boy Bull Bar!
- Replies: 5
- Views: 720
- Thu Mar 19, 2009 8:00 pm
- Forum: For Sale
- Topic: WTB 800cc gear box
- Replies: 0
- Views: 235
WTB 800cc gear box
Hi I'm after 800cc gear box NSW asap. thank you
- Thu Mar 12, 2009 1:38 pm
- Forum: Suzuki MightyBoy
- Topic: Gear Box Confusion
- Replies: 5
- Views: 360
- Thu Mar 12, 2009 12:42 pm
- Forum: Suzuki MightyBoy
- Topic: Gear Box Confusion
- Replies: 5
- Views: 360
Gear Box Confusion
Hi Guys In my mighty boy I have a 800 motor ( engineered ticket) with what I think is a 800 box, had bearing noise, pulled it apart and found the rear bearing on the input shaft burnt and very noisy to top it off broke a bolt in the lower housing between the input shaft and the cluster shaft :cry: t...
- Sun Mar 08, 2009 9:11 am
- Forum: For Sale
- Topic: For Sale: (NSW) 800cc Motor/Box/CVs (all running gear)
- Replies: 3
- Views: 510
- Tue Feb 10, 2009 6:09 pm
- Forum: Suzuki MightyBoy
- Topic: Front Wheel bearings
- Replies: 1
- Views: 217
Front Wheel bearings
Hi all, my front left wheel bearing is a little noisey, I know it's not the CV. has anybody replace these, I have checked and parts are around as a kit. 1 inner and 1 outer + seal. or would it be better to take hubs off and take to a bearing place, i have a press but haven't pulled one of the M/Bs a...
- Fri Jan 16, 2009 7:26 pm
- Forum: Suzuki MightyBoy
- Topic: This may have been done. If not.. looks good
- Replies: 0
- Views: 332
This may have been done. If not.. looks good
What I was missing in my M/B was a dash clock. My son is restoring a Suzuki Sierra with a 92 damaged one for spares. I looked at the dash clock in this and thinking this one would look good in the M/B where the square Suzuki panel is on the dash next to the heater controls, so I went about pulling t...
- Sun Dec 28, 2008 9:32 am
- Forum: Suzuki MightyBoy
- Topic: Gear box rebuild
- Replies: 13
- Views: 1114
- Sun Dec 28, 2008 9:27 am
- Forum: Suzuki MightyBoy
- Topic: fuel guage not working
- Replies: 5
- Views: 503
Yep. but check on wiring. 95% of fuel sender units are Neg activated by grounding the wire you are bypassing the resistance in the coil in the unit in the tank the wiring that gives you the varance on fuel levels ie 1/4, 1/2, 3/4 which is moved up or down via a float lever. so when you ground the wi...
- Thu Dec 25, 2008 1:39 pm
- Forum: Suzuki MightyBoy
- Topic: Gear box rebuild
- Replies: 13
- Views: 1114
Thank you for that Brayden, there is no noise when the clutch pedal is depressed all goes quiet. so it seems the front bearing in the box could be the noise the thrust bearing is used to depress the pressure plate. when I put the gear box in ( 2nd hand) I replaced the clutch and bearing and also the...
- Tue Dec 23, 2008 11:24 pm
- Forum: Suzuki MightyBoy
- Topic: Gear box rebuild
- Replies: 13
- Views: 1114
Gear box rebuild
Hope some1 can help...I have a bearing noise in the input shaft of my gear box (f8b), can anybody help where I can get a rebuild kit or a supplyer of bearings. I went to repco and scotts with no luck as the guy said he had no listing :x ( there is no noise when I put my foot on the clutch only with ...
- Tue Dec 23, 2008 11:12 pm
- Forum: Suzuki MightyBoy
- Topic: Vibration at idle to 3000 rpm (F8B)
- Replies: 4
- Views: 368
- Tue Dec 23, 2008 11:05 pm
- Forum: Suzuki MightyBoy
- Topic: fuel guage not working
- Replies: 5
- Views: 503
the fuel and temp guages are Negative activated. so to check your fuel guage disconnect the sender wire from the tank (can't remember if it is easy to get to) earth it out with the ign key turned on (motor not running) the fuel gauge should move slowly to past full mark if this happens the gauge may...
- Sun Nov 16, 2008 9:22 am
- Forum: Suzuki MightyBoy
- Topic: Strange Question
- Replies: 11
- Views: 822
- Sat Nov 15, 2008 9:03 pm
- Forum: Suzuki MightyBoy
- Topic: Strange Question
- Replies: 11
- Views: 822
Bingo, thank u Ike849. took the wheels off and the only thing I found is some marks on the OSF inner plasticguards under the fender.and a small mark on the lip of the guard at the top. I'd say this is it.... thanks Brayden I will take the struts out and chase up some new inserts. Does any body know ...