F8A and gearbox
Diff
Rear metal bullbar
F10A carby
Black plastic headlight surrounds x2
New aircon hose (compressor to condenser)
+ whatever else i can find

$150 the lot

0401 622 286

Located NOR Perth WA

thanks

-ian

as above 14x6 not 100% sure on offset, but i do know this is probably the most aggresive fitment you could go on a sk410. just clears the rear doors located NOR perth $750 pics here: http://www.gumtree.com.au/s-ad/duncraig/wheels-tyres-rims/set-of-4-rs-watanabe-14x6-4x114-3-with-new-tyres-175-60r14/...

Hey Jezza! I joined up to have a looksie, nice to find you on here. Let me know how you go with your side of things. I'm looking at drilling out the standard exhaust manifold, adding injectors and modifying an S13 SR20DET Apexi Power FC to suit the carry van EFI + Turbo. Other than that, trying to ...

my temp stays just below half most of the time (approx 40% across) goes up a bit higher during freeway runs the fan does not run a clutch it is bolted straight to the water pump. i know this because i overhauled my maruti engine and ha dto do all this. a thermofan should give a good performance incr...

no.3 is a da32v 01 suzuki carry van

notice the difference in size between in and my sk410

bought this with a friend as a run around car

stock apart from 15" mags the previous owner put on

no.2 is a da32t 200 suzuki carry AWD ute. standard apart from lightforce spot lights not a true 4wd but very capable offroad. loves going through soft sand, where bigger 4wds get stuck. mods - old roll bar removed. new one on its way from japan. will mount spotlights to this - removed plywood tray l...

hi all, been on here for a while now, so i thought i would post up about my 3 carry's http://www.skylinesaustralia.com/forums/uploads/1329399331/med_gallery_13664_543_2038.jpg http://www.skylinesaustralia.com/forums/uploads/1329399331/med_gallery_13664_543_10637.jpg http://www.skylinesaustralia.com/...

pretty sure CEVA are the biggest car carrier in Aus

just took the rear drums off my carry and they appear to be self adjusting?
ratchet type system

hi, if you do not use the full load capacity you could go my way: front: cut away three windings of the coil spring on each side cut the rubber bumpstop in half and remove the cut piece rear: cut rubber bumpstops down add 2" ford escort mk1 lowering blocks remove one spring leaf and the overlo...

My bad! I thought TB was a Cordia model. The Suzuki shop in North Heidelberg told me they are rare and to buy a spare at $60 which I did. The coil on ebay is a normal 2 pin coil. So, if the third pin is to go to the carby will it still work if I bought on of the electronic modules with a 2 pin coil...

jezza

so how did you decide to lower your car?

also any idea on the width/offset of the wheels? and the tyre size?

will be good reference for others on here

thanks

Mine is a 4 cyl and the coil has a positive, a negative and another in the middle of both. That is why the coils are expensive and becoming harder to acquire. i do not believe coils are hard to find they are quite universal and readily available eg high popular bosch gt40 http://www.ebay.com.au/itm...

Thanks Brayden, Correct I am only using the TB From my understanding of how a coil works, it fires each plug in cylinder. So if you have a 3 cyclinder, you should have 3 contact points If you only use 2, then you really only got 2 cylinders firing lol Still working on the TB.. im not sure if its th...

elec ignition kit http://www.ebay.com.au/itm/Bedford-Rascal-Electronic-Ignition-Kit-POWERSPARK-/110690276933?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item19c5a79645 with coil http://www.ebay.com.au/itm/Bedford-Rascal-Electronic-Ignition-Kit-Lucas-DLB105-/120749341203?pt=UK_CarsParts_Vehicles_Ca...